Wireless Bridge PTMP WiFi PTP Access Point To Point 5.8G Outdoor Network CPE220 2KM Transmission Distance With 12DBi High-Gain Antenna 2 LAN 100MBps Ethernet Port 24V PoE Power Supply 2 Pack

• CPE220 wireless bridge is a 5.8G Long Range WiFi Extender Outdoor CPE with a digital display. It complies with the IEEE802.11a and IEEE802.11n,standards to ensure interoperability. Point-to-point pairing also can be done by dialing without having to access the GUI, avoid the complex setup program, save much human work and cost, make the long-range wireless coverage, data transmit, and wireless monitoring simple and professional.
• PTMP Pre-programmed: Out of the box, connect the 2 WiFi bridges and PoE adapters through the ethernet cable for power supply, and wait for 1 minute for the "Link" green indicator to light up to indicate that they have been automatically paired succeeded(Point to Point). Suitable to extend the internet to your garage, barn, warehouse, store via wireless transmission, instead of laying out the ethernet cable.
• Using 5.8G / 300Mbps wireless transmission rate between network bridges can support 2KM transmission distance(Barrier-free), and can provide up to 100Mbps wired network speed, suitable for connecting the networks in 2 or more buildings, internet access sharing, remote video camera surveillance, or remote network WiFi access.
• Extend the network to another building within 2KM through a point-to-point method. The master outdoor CPE receiver is connected to your internet through a PoE adapter, and the slave CPE transmitter is connected to the router(AP mode) or directly to the computer through a PoE adapter to expand your network/WiFi to another building, such as expand your home network to store.
• Realize remote camera video surveillance or elevator monitoring through wireless bridge point-to-point or point-to-multipoint. The master CPE receiver is connected to a DVR, or monitor, or computer through a PoE adapter, and the slave CPE transmitter is connected to an IP Camera through a PoE adapter to expand your camera surveillance range. Reference pictures are easy to connect CPE with IP cameras & networks DVR.

CPE220 5.8G Wireless Bridge Kits to Extend your Network

Extend your network from one building to another without wire connection CPE220 5.8G Wireless Bridge with 300Mbps and 1.2 Miles Data Transfer Range

CPE220 wireless bridge kits is one pair of outdoor high power and high performance 300Mbps wireless bridge, which works at 5GHz frequency. Supports Point-to-Point and Point-to-Multipoint wireless connection. It is more stable and higher speed and anti-interference performance than 2.4GHz wireless bridge. Moreover, it is easy to manage through the WEB interface.

CPE220 Wireless Bridge Kits Function:

A. the device can works as Auto pairing mode: simply to use, connect both bridges to the PoE power adapter to start working, it will auto pair in few minutes. Customize mode: need connect the bridges to the computer through ethernet cable, and configure the master & slave parameters, this mode suit for experienced technician.

B. the device can use for share internet networks to a long distance, output WiFi hot point, also can use for transmit the long ranges IP cameras' video stream to the control center without complicated wiring connection.

C. Auto pairing mode works for point-to-point access connection, customize mode can configure the point to multiple point connection.

The CPE220 kits is great to extend your home internet network to another building without wire connection, you can share your network to your barn garage, warehouse, workshop or small store near to your home, it also works for enterprise to share the internet from different office, workshop, warehouse and etc.

We offer a pair of wireless bridge in the package, we need to set one works as master mode, and another works as slave mode.

Wireless Bridge Master & Slave Set:

1. Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2. Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Point to Point WiFi Internet Access

Share your WiFi from one building to another without wire connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the router through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the computer or router by another ethernet cable

The master bridge transfer data to slave bridge works as point to point mode to extend network access to another house, office, building for internet surfing. The master bridge also output WiFi hot point, you can open the WiFi connection setting on your cellphone, or laptop, you will find the WiFI name CPE5G_5Gxxx, enter the password to get access.

The access password is pre-programmed, it is different depend on what channel the wireless bridge working, but only change the last two or three numbers.

For example: the WiFi hot point name is CPE5G_5G161, and the default password is zllinkcpe123456161, if the name is CPE5G_5G153, the password will be zllinkcpe123456153, the last three numbers of the password is match to the last three numbers of the name, zllinkcpe123456 is the same, you can find the password with a little bit change for the different channel.

Point to Point Video Surveillance

Extend your video surveillance network cameras range, connect all the cameras on one DVR system

Wireless Bridge Master & Slave Set

1.Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2.Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the switch by another ethernet cable

Point to Point video surveillance, expand your video surveillance range, easily management all your surveillance camera in one DVR system without complicated wiring. Transfer your video surveillance network IP cameras data from another building to your DVR, easy to management all the cameras in one system.

Point to multiple Video Surveillance

Point to multiple point video surveillance network camera system connection

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the IP cameras by another ethernet cable

Install the slave bridges face to face to the master bridge, and the direction angle no more than 60 degrees, this connection need login into computer to configure the IP address for different slave, please read the user manual for details.

In this way, you can easy transfer the network camera video streaming from different buildings to the DVR of the control center, point to multiple point function is great for you to monitoring multiple buildings without complicated wiring.

Wireless Bridge Interface

The CPE220 wireless bridge kits works by two modes, auto pairing mode with pre-programed suit for newbie, customize mode suit for experienced user.

Auto pairing mode:

connect it to the PoE power adapter, the Power LED turns green on, system is power on, when the both bridges all are power on, it will auto pair in few minutes, the pairing and LAN status LED light all turns green on. the digital LED indictor display the numeric in red color.

you can press the "RST" button to change the channel to find a good frequency without interference, short press the button, the LED indicator will display the numeric "0","1","2","3"..."F" one by one, and change in cycle, each numeric means a different frequency, you can find the details on the user manual.

Customize mode:

at this mode you need connect it to computer and set the different IP address and working mode, short press the "RST" button will not functional at this mode, but you can press and hold this button over 10 seconds to reset to factory mode.

One Master Bridge to multiple Slave Bridges One bridge works as master mode, the other two or more bridges works as slave mode, all the bridges need to install as face to face, for multiple point connection, the slave bridge direction angle no more than 60 degrees.	Matching the master and slave bridge channel Adjust the slave bridge channel to match to the master bridge, the both bridges will be auto paired in few minutes.	WPA2-PSK Encryption The bridge output WiFi hot point with WPA2-PSK encryption to keep your network in safety, do not worry your privacy to be exposed.

Parameters

Model:	CPE220
Network Interface:	10/100Mbps 2 * LAN Port
Data Rate:	11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps / 11n: 7.2M, 14.4M, 21.7M, 28.9M, 43.3M, 57.8M, 65M, 72.2M, 14.4M, 28.9M, 43.3M, 57.8M, 86.7M, 115.6M, 130M, 144.4Mbps
Power Supply:	POE 24V 1.0A
Antenna:	12DBi (5180～5825MHz)
Transmission Range:	2KM / 1.2 miles
Waterproof:	IP65
Dust-proof:	Support
Working temperature:	-4℉～158℉
Dimensions:	170mm * 90mm * 60mm / 6.67'' * 3.55'' * 2.36''
Weight:	0.7kg / 24.7 oz